Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi,
I have a custom board with nRF52832 with external spi flash and I'm using SDK 17.1 and softdevice s132 4.0.5. I will use OTA-DFU to receive the new firmware image from...
Like several other folks, I have been attempting to replicate the results in the Matter webinar here , but updating to the v2.1.0 SDK and using the Nordic dev kits I have...
Hi ,
I am working on NRF52840 microcontroller, I want to implement blinky LED for P1.09 GPIO pin, can you please tell me, how to implement that.
Thanks
Hello!
The company that I work for has built a gateway that uses the nrf52832 as a ble central device (nrf5 SDK and the s132 softdevice). Customers frequently ask us to...
Hello Nordic support:
How to reduce nRF9160's LTE-M TX power in coduction test. Is there any AT command to reduce TX power? Or could you give us some guide about how to...
I am diagnosing pin malfunction in a custom board where I have working code from another version of the board which no longer works.
I am developing against NCS w/ VSCode...
Hi,
When asking to change the toolchain version in the VSC extension I get an error message:
Command 'nRF Connect Select nRF Connect SDK Toolchain' resulted in an error...
I am using the current nrf-sdk v2.1.0, which includes a Zephyr version (3.1.99 etc.) which has at the used stage an error with twister: instead of using get_testsuite the...
Hello,
I tried to run the sample Bluetooth: Periodic Advertising but I found some issue.
I'm using SDK v1.9.1.
The first issue was related to advertising creation with...
Before I go deep into the rabbit hole, I am wondering if anyone has had success with the following:
I am in a Windows 11 environment
I want to setup Docker with nRF...
Hi Community & Nordic Semi
I have an ultra low power design using the NRF9160.
I would like to avoid adding an additional LDO to reduce costs and Iq.
VIO from the datasheet...
Hello Community, i'm currently working on a custom board based on BC40C which is a BT/BLe module based on nrf5340 i'm trying to debug my board with jLink ultra + under, i...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
