Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello,
I have been working with custom nrf52832 board to develop firmware for my product. I have been trying to compile the example secure bootloader from the SDK v15.3...
Hello, I am developing a uart communication between the nrf52833 and the nrf9160. I found some examples but I don't want to use the HCI layer, I prefer to use the NUS service...
Hello
OS :- Linux
Hardware version :- BC805M
SW :- Segger embeded studio
I am using nrf52805. I am test it with ble_app_uart. It advertisement continuously and shown...
Hello,
I'm trying to transfer data to an L2CAP CoC on a nRF52832 from iOS and Android devices. I've configured the MTU and MPS so that the SDU fits in a single packet with...
I'm using BLE Mesh Sensor example that Client & Sever communication data each other.
Because I'm implementing one by one communication data that client > sever > client...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to add a custom UUID in the advertisement packet and scan for the custom UUID in the central device to...
Hi,
Our firmware currently only support full modem update, and I would like to perform a full modem firmware update from 1.2.0 to 1.2.7. According to the reply from https...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
I am getting a softdevice hard fault occasionally, on fully enclosed devices with no debugger port access.
Where can I find info on potential causes of this fault?
nrf51822...
Hi
I have a question about reset Bluetooth, how can I do that?
I don't want to reset the system only to reset ble, turn on and turn off the ble,
thanks and regards
Hi guys,
This is my first BLE project. I want to send sensor data from my nrf52840 dk to my dongle. I know how to make an advertise but I can’t find a way to send my sensor...
Hi!
We'd like to understand the most reliable way for DFU OTA our Nrf52840DK boards over a "serial" topology network?
We are using nRF5 SDK 15.2.0 and our configuration...
we have nRF52832 controller
now we would like to choose the softdevice S132 or S112
how can i select the softdevice?
where can i find the difference between S!32 and...
Hello, Technical support team
In the past, I contacted you to confirm nRF52832 application.
This time, I have a question for a external reset as follows.
My application...
