Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
Hi,
I enable the watchdog in the application image, then call soft reset to enter the bootloader, the bootloader execution is also normal, until the watchdog is reset. ...
Hello!
I have a situation where a chip is connected with an antenna on a u.FL slot, what I want to do is to remove that antenna from the chip and connect my nrf52840 to...
Hi,
I want to send the I2S MIC Raw data through Ble by using ble_nus_send. I have written one application but it triggers a Cmake error. I have attached the log below...
HI I'm using the nrf5340dk, and I'm able to flash the application core with code that toggles the LEDs.
But I'm not able to flash the network core. I've specified in the...
Hi, I'm currently designing a system which requires Heart Rate monitorization and I'm using the MAX30101 chip to do so. I will be using I2C communication and, therefore, based...
1. We use code similar to the existing sample code to repeatedly sample a 0 - 2.25V voltage range using the SAADC. 2. Settings: 30s interval, single-ended input, burst-mode...
Hi All,
I'm looking for a PC based tool with similar functions as nRF connect. Our manufacturer is developing a functional test fixture which will PC based and will be...
Hello,
I'm looking for reading the sent data from an old embedded autonomous nRF905 (which act like an active tag) and I thought I could use this convenient-looking USB...
