I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I have two custom images that I flash to my chip (nRF52832, SDK v16.0.0, SEGGER Embedded Studio). Application 1 is located at 0x26000 Application 2 is located at 0x45000....
I am new to embedded f/w development. I would like to be able to debug zephyr projects. Can anyone recommend a debug probe to use with the nRF5340? and any debugger software...
Are there any other SDK options for nRF5340 than nRF Connect SDK (and Zephyr)?
The chip would be nice, hardware-wise, to a project, but the nRF Connect SDK looks like a...
I am having a similar issue to the person in this post where the wake from deep sleep on an interrupt sometimes works and sometimes doesn't. But for me, it's very consistent...
Hello,
I know this question has been asked a lot. But I haven't found one that matches exactly. I'm trying to flash a custom PCB with an nrf52832. I'm using the on board...
Hi,
I am trying to get a simple LED blinking using a timer, gpiote and the ppi. So the Idea is:
Timer compare event -- PPI --> gpio toggle. I am using the nRF connect...
HI,
I am developing an application which requires BLE connection. I am concerned about the energy consumed by the device during the connection.
I understand that once...
Hello,
I'm just starting to use Asset Tracker V2 from v1.9.1 and it appears that it is missing some device info such as version, carrier and other on the Device Information...
Hello,
I'm trying to send a custom reliable message between two nRF52840 DKs, using the nRF5 SDK for Mesh v5.0.0 and nRF5 SDK 17.1.0, by modifying the light_switch examples...
Up to now I referred to the name of the tag from the west manifest to know the zephyr release. So I assumed that the v2.7.99-ncs1-1 tag was from the zephyr 2.7 branch until...
After executing nrf_libuarte_drv_rx_stop(), nrf_libuarte_drv_rx_start() will produce an error.
In nrf_libuarte_drv_rx_start() t his line in nrf_libuarte_drv.c (Line 625...
Hi ,
i am working on nRF52833dk board. here am running sample example from sdk. i.e. peripheral_lbs example. my query is whatever the Bluetooth api it is calling inside...
Hello,
In my project i am using ble_app_template example of SDK version 17.0.2 i need to send some data to device nrf52810 from the nrf mobile application. so i have tried...
Hi all,
I'm trying to connect an ESP32 with an nRF52-DK (nRF52832) through I2C. I'm using the ESP32 I2C Slave example ( https://www.arduino.cc/reference/en/libraries/esp32...
