Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Screenshot of error message
Hello, I've followed the steps required on YouTube for setting up VS code with nrf Connect for desktop and the toolchain manager. It didn't...
Hi Team!
Currently I an working on disabling JTAG/Debug and SWD lines to protect code from read/write through any JTAG debugger.
For this, I have used nrfjprog utility...
Hi Support team,
I am testing nRF5340+nRF21540 with MT8852B now. I come across two issues in running the DTM FW from nRF Connect SDK v1.8.0:
1. nRF21540 TX gain value...
hi， I'm working on passthrough firmware(nRF5_SDK_17.1.0_ddde560)，I need to increase the priority of the serial port,see following code,When APP_UART_FIFO_INIT priority set...
Hello, in my zephyr application, I have uart1 configured as receive only using uarte at 921600 baud rate. Below is the description node:
I have a device sending a uart...
Hi,
We are using nRF52810 on a custom board, and when creating that board in NCS (in VScode), the Kconfig options are limited. We are not able to enable/disable the DCDC...
I have a project using NCS v1.8.0 where I enabled openthread.
For some reason, when trying to build `mbedtls/library/ecjpake.c`, the make command uses `-DMBEDTLS_CONFIG_FILE...
Hi! Im doing a SPI transaction using EGU and PPI. Software triggers the EGU, and PPI_CHANNEL_1 uses this event to start the SPIM transaction and set the CS pin low. PPI_CHANNEL_2...
I have followed the procedures to create a DFU package
- Using existing sample hex file "hrs_application_s132.hex"
1. nrfutil keys generate private.pem
2. nrfutil pkg...
I am using SDK V1.8 and have noticed that RTT output will run for a short time then stop.
Debug is still running because breakpoints can be set, just no printk output or...
Hi, guys.
I have been using NRF Connect SDK 1.8.0 , I want to use this
"v1.8.0\zephyr\samples\application_development\out_of_tree_driver"
to develop my custom driver...
Hi,
I'm developing a miniature application on nrf52805. I got an nrf52-dk and I am trying to understand which SDK i should use.
So far my problem is that on one hand ...
I'm trying to transition from Embedded Studio to VS Code. I have a sample application that I created in VS Code that builds without error, but when I start the debugger I...
Hi,
I am trying to setup a TWI interface between the nRF52 DK and the 16-bit ADC ADS1115 from TI. I am using the breakout board from Adafruit ( https://www.adafruit.com...
Hi,
I use nrf52832, SDK 16 and SD s132. I use FDS to store application data (fixed size), and I use bonding too. So the peer manager also store the peer related data in...
