I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Yes, I have seen the many other tickets with this subject name, but they did not solve my problem. All of the directory paths in my "User Include Directories" in Project preprocessor...
We have a running sensor system with four sensors sending data to one central node (all nRF52840 Dev Kits). The nRF Mesh App was used to provision the nodes.
Now when...
Hi,
I use NRF52832,SDK17.1 ,softdevice is s132.
I shielded the part I added by myself in ble_uart example, but it will prompt this error about 1min after power-on. How...
Good Morning and a Happy New Year,
I try to test an application, using the nRF Connect for Desktop (on a Mac). While trying to pair with an application that supports LESC...
Hello All,
I've had some success now connecting my 52840 Dev Kit with the NRF52840 Dongle and would now like to use the dongle as a receiver with the PC-BLE-DRIVER-PY library...
Hello,
Does the nRF Connect SDK support enabling QSPI encrytpion (DMA, XIP)?
I see there are two functions in the nrfx_qspi.c that do this: nrfx_qspi_xip_encrypt and nrfx_qspi_dma_encrypt...
Is the nRF51 SDK version number exported as a preprocessor #define in any of the SDK header files?
Because the SDKs are not backwards compatible to different revisions...
Hi,
I designed a bluetooth device that stores 8kb of data. With 20ms connection interval, data is sent to the smart phone in 3 minutes which is to high for this project...
Hello.. I want to access the nRF5340 registers to maniulate there values, for example : If, I want to acess the PSEL.RTS register or CONFIG of UART0 to initialize these. How...
Hi.
I am following the tutorial "Developing Matter products with nRF Connect SDK" but having problems getting the openthread border router working with the raspberry pi...
I am using the board with MQTT simple software
when I am activating one a signle EVB, it works well
however when I am activating on two board in the same general location...
I noticed in Zephyr OS there is an API LED:
led_on(dev_io, RED ); <-- does not work gpio_pin_set(dev_io, RED, 1); <-- works well
what can be the reason ?
can you...
Hello everyone. I have just started with the eval board uBlox NORA B1 (NORA B-106) and I am trying to find a starting point for streaming audio via Bluetooth Handsfree protocol...
Hi Nordic：
I use the LWM2M of NCS and found that the power consumption increases every 2.5 seconds. I use the monitor to find that the serial port is sending data. How...
