I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hello,
I am testing the 1 CENTRAL module with 4 PERIPHERAL module connection.
So I set the
NRF_SDH_BLE_CENTRAL_LINK_COUNT 4
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 0 ...
Hi,
I have two custom boards, one is central with nRF52933 and other is peripheral with nRF52832.
In the previous test, the connection between the 52833 central board...
Hi Team
Because Ble_2Mbit have better RX sensitivity than Nrf_2Mbit. Can I use Ble_2Mbit in ESB code? Is there any potential technical or legal risk? thank you.
regards...
Before updating to V2.00, the DTM tool can automatically detect the serial port, log has a clear indication whether it is connected to the target board, when the DTM update...
Hello.The SDK version I'm using is 17.0.1 and the protocol stack version is S140_7.2.0. I use the nrfutil to generate the update zip file for dfu,but I find that the nrfutil...
Hello! I have the whitelist support for my device with the default settings:
My goal is to rewrite saved addresses in the whitelist, when there is a new 9th address bonded...
Hi,
I'm working on adding the buttonless DFU function to my application. It works fine when I disable NRF_PWR_MGMT_CONFIG_AUTO_SHUTDOWN_RETRY in sdk_config.h . However,...
Hi everyone.
I have a custom board with nRF52832. I am using J-Link for programming. In my custom board, SWD pins are exposed. So I can erase nRF52832 succesfully and programmed...
I have recently switched from development with the nRF52832 to the nRF52840 and along with this switched from the nRF52-DK to the nRF52840-DK. I am unable to connect to the...
Hi everyone,
I try to connect simulatanoues 12 BLE devices to a Linux PC with Bluez.
You cannot go above 5 with commercial BLE controller.
So I want to use the dongle...
As many others have found, and answered questions here and here and in other posts, DFU will prematurely exit IF you have enabled WDT in your application, as the current Nordic...
Dear Nordic Engineers
I recently encountered a problem when developing NRF9160.I developed it based on the example of asset_tracker_v2.Now I have an .a file of an encryption...
I am using SDK 15.2 with Segger Studio
I am using an external button on pin 4 to enter sleep mode on a long press and wake up the device.
I am able to enter sleep...
Hi
I am using sht85 to detect temperature/humidity in my Light lightness server code
In the original server code, by pressing 1 or 2 you get to either decrease or increase...
Hi,
I'm working on a project using the nRF9160 (NCS V1.7.1, V1.3.0 modem firmware) and am utilizing the 1PPS signal.
It is working well, however when the fix is lost...
