I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
Hi,
I'm working on a multilink central device with SDK16, nRF52832.
I'm trying to connect the central to 2 peripherals with certain address. So I added 2 address filters...
Hi all,
I have a nRf52832 Buttonless DFU setup and application is BLE APP UART.
nRF52 SDK = 17.0.2
I need to send a hex file of STM32F4 through UART. Do you have any...
Hello
I'm using sdk17.0.2. And I'm using the ble_nus service with the addition of nrf_crypto (AES_CTR).
I originally used nrf52832 and pca10040 and the test went well...
I just got a new nrf9160DK rev 0.15.0. While plugged in to USB and the switch in the off position, my meter reports 4.95V and 0.016A. Why is this happening? My older rev 0...
From the product spec, the voltage accuracy is listed as -10, +5% from the programmed value. We're using 3.0 V. For our application I need some more specifics on this regulator...
Hi,
I'm building DFU secure_bootloader with oberon crypto library as mentioned here https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts...
Hi,
I'm developing an Android app using the nRF Mesh Library. I have a scenario in which a few phones need to be provisioners given that these will configure new nodes...
prj.conf of light demo:
Can you tell me where CONFIG_LOG is enabled? It is inconsistent with ncs1.5.0. When I enabled CONFIG_LOG_BACKEND_RTT, I was notified of an...
I am trying to program a PCA10059 USB dongle which requires it to go into DFU mode.
I have tried pressing the white button when it is plugged in, and I have tried holding...
I can't seem to find the answer here - sorry if it has already been answered. We were having an issue recently where the root cause ended up being that we were trying to do...
