Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
I need to do batch DFU updates, and the pc-ble-driver/nRF Connect Firmware combo is too unreliable for my needs. I would prefer to just use the wireless transciever built...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
Hi,
Currently I am experiencing some issues regarding flashing the modem firmware on the NRF9160. My end goal is to automate the process of flashing both modem firmware...
I am using SDK v12.3.0 for nrf 51822 chip. I am working on hrs example with some custom modifications, so i need to to update application through OTA, i have used bootloader...
Heija Guys,
I have a problem with my PWM. I started with the zephyr version 2.4.99 and switched, after we discovered a bug (Link to ticket: https://devzone.nordicsemi.com...
Good Afternoon, Im using a samsung galaxy tab a - Model num SM-T510 Android Version 10 nRF Mesh app version - 3.1.5
After provisioning 14 nodes, whenever i try to reset...
Hi,
I am trying to integrate UART and DFU serial from the mesh example.
What I did is:
1. Adding uart drivers and libraries into the DFU project.
2. Adding codes...
Hi,
We are seeing the issue mentioned in https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in-saadc-samples-with-easy-dma-and-ble/79053#79053 . We have 2 sensors...
