Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
We're using nRF52840 with S140 SoftDevice (version 7.0.1) and 16.0.0 SDK. When USB cable is connected before USB initialization we receive correctly APP_USBD_EVT_POWER_READY...
I am very new to the Embedded world and very confused about some stuff, I have searched the internet for 8 hours and then asked here.
I am being assigned to the task of...
Hi!
I'm developing application on nrf52832 development board which will be a work indicator - for office desk ;) Main idea is that i have client based on nRF MCU and desktop...
Hi, I am searching the nRF52810 product spec and see that with standard drive, maximum GPIO output current appears to be 4mA. However, this spec is given for when the output...
Hello, I am working on SDK 1.3.0, I have an NRF9160DK and I am migrating to a custom NRF9160, I would like to output the log by moving the pins of the UART. However, it is...
We have ported from SDK v15 to v15.3 but now have a problem getting the USBD to start.
Below is a sort of pseudo-copy of our USB init routine which is working for us on...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
I have bought new thingy 91 from mouser. Com. I burnt the latest pre complied hex file for assist tracker. I am getting all data except gps.
it is not getting connected...
I have a custom firmware developed on a nrf52832 SoC. I would like to know if i could see nrf logs such as nrf_log_info and nrf_log_debug via bluetooth? if this is possible...
Hi!
I want to use a TensorFlow Lite for microcontrollers model in my existing project built on top of the nRF5 SDK. However, as outlined in the nrf-tensorflow example ,...
Hi ,
I has been using NRF9160's AT client mode to connect with CMW500, however I found some problem.
The following is the command log that I used to send via UART. However...
