I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
With regards to the HID Keyboard Example,
1) Is it posible to disconnect from the central side (ios)? I would like to be able to disconnect as follows:
But...
Hi,
I have just started using the Nordic SDK (nRF5_SDK_15.2.0_9412b96) and am developing a low power application for a custom PCB using the rf52840.
I am developing...
I can read the spi flash id by the other mcu with the above code, but can not read correctly by
nrf52832, is there something wrong with my handle?
SPI FLASH ID 0E 40 13...
Hi!
We experience some problems with DFU, and while looking through the code, I saw the code copied below.
This is from the file dfu_req_handling.c from SDK14, and my...
Hello everyone,
I am programming my dongle(nrf52840) with my Dk. To upload the code I click on download "solution_name" in the target menu, it works fine for example without...
I am using NRF52840 Dongle to scan all the BLE advertisement packets.
I wish to scan for the BLE advertisements packets only from a particular device using the whitelisting...
hello all,
i am trying to add ble app uart feature in other ble app project. so i am trying to change those defines variable, NRF_SDH_BLE_GATT_MAX_MTU_SIZE & NRF_SDH_BLE_VS_UUID_COUNT...
1. In the ssdk:ncs v1.3 Example: in 10_hello_world_clock_gettime, test function: clock_gettime (CLOCK_MONOTONIC, last_action_time);
The following error occurred at compile...
Hello,
nRF52811, SDK16.0, Softdevice7.0.1
We had developed our application based on nRF Blinky Android sample app for nRF52840. Now we want to port same app for nRF52811...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
Hello
I use nrf52840, Keil uvision 5.26, Win10.....
when i test the board, program run into hardware fault.
that reason is No I2C response, and i delete int the I2C...
I am developing a device which will have Nordic's UART service and it also need to be able to bond with the central. I am using SDK 12.0.0 and VisualGDB for my previous projects...
I'm working on getting an eclipse project working for my nRF52840 application that is currently working with a Makefile. My issue is that once I reset the board, or power...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
