I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi everyone,
Im looking to put together a security solution consisting of an accelerometer and a proximity beacon. The accelerometer would be installed on gates and authorized...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
Hello,
i noticed that even i send AT%XMODEMTRACE=0 with response "OK" the bsd lib triggers EGU0 / Trace interrupts. The modem is not started, but the bsd lib got succesfully...
We are using a Raytac MDBT42Q (nRF52832) Bluetooth in one of our products.
We are using nRF Toolbox for Android/IOS for testing. Is there any Windows 10 nRF Toolbox??
...
hi guys, I'm confused about bluetooth 5. Is there some example that use it? i have a nrf52840 board and i will like to use it in order to send my data but i didn't find any...
HI
I am trying to develop a mesh network using nordic mesh SDK..where nrf52 dongles will be beacons for which beaconing example will be used and from SDK
52840 DK will...
I startet evaluation with nRF52840 and SES.
I found the BSP Demo to crash (HardFault in Debug) after app_timer_init() , because of a NRF_LOG_INFO() inside, but Logging not...
Hi Sir,
As the title, can 51824 support BT 4.2 in Zephyr? Any document (or link) descript this?
If yes, which SDK version we can use?
Thank you.
BRs, Han
Hello,
I am working on nRF9160dk. I want to send gps coordinates via sms using nRF9160dk. Last week, I tried simple_at program to send sms and it worked. Now I am working...
When I am receiving data from slave data is missing. Means if o am reading 255 bytes then 127 bytes are right after that I am receiving alternate bytes. Some times I am receiving...
Hi,
I was wondering if anyone has sample code that would support a 16 x 2 LCD over an I1C interface.
Something like this.
https://www.amazon.co.uk/HALJIA-Character-Backlight...
