I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
Hi
We use the nRF51822 with s110 active. As long the s100 isn't active, we can debug, set breakpoints, stop, continue like it should work.
When activating the s110 and...
Hello,
The question is about CUSTOMER area in UICR. After locking chip wirh UICR.RBPCONF.PALL I noticed that I still able to read UICR.CUSTOMER data.
Could I enable readback...
Hi all,
Google launch uWeave Library project.
uWeave is an implementation of the Weave protocol intended for use on microcontroller based devices.First demo project is using...
Hi,
As first stage of planning our next generation of wireless sensors at my workplace, I must carefully consider which radio protocol suits us best. We don't need sub 1...
HI,
Hi,
I have been working on nRF5 Development Kit where Basic configuration is working i.e. blinky program and when I load peripheral program(PWM,UART), its also working...
Hello. I have several nRF51 devices (nRF51 Dongle, pca10031) I wish to use as BLE link between robots.
Is there any examples or tutorials that show how I can do this...
Hello
I am working on the NRF51DK i would like to monitor the battery percentage and notifythe value over the air to the user and aslo alert the user if the battery levels...
I have to develop my own Dfu central to update my nRF51822 peripherals over the air.
Could you provide sourcecode for one or more of your Dfu central applications like: ...
I ve already found this post regarding the AutoConnect Issue.
devzone.nordicsemi.com/.../
I have the same problem with a Sony Xperia Z on Android 5.1.1 ...
Is there...