I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
I'm writing a build script for gcc for the nRF51 and I want to use the provided .ld scripts.
In SDK 8, those scripts were renamed from gcc_nrf51_XXX_xxab.ld to nrf51_xxab...
Hi,
I want read accel data from BNO055 sensor to NRF51 DK board, but SCL and SDA pins are 1 always.
My code is the next one:
#include "twi_master.h"
#include "twi_master_config...
I have existing design with I2C accelerometer on P0.1 and P0.2 (SDA/SCL). Don't need extreme data rates. Since examples of initializing on-board TWI don't seem to exist, and...
I am developing a tool that will be using the existing NRF51 dongle to run the S130 SD and it is being written in Python. There is no way to change any of these parameters...
Does anybody have a suggestion for a relatively low cost way to test the output power of a nRF24L01+ module? We make the modules (which are identical to the demo module) in...
Hi,
I am using the GPIOTE->PORT event to detect button presses and I would like to detect both button press and button release.
However, it seems like SENSE can only...
(this is duplicate with a support case I just opened... I hope that's okay.)
Hello, I am setting up a new laptop (our development machine caught a virus) and have installed...
Hi,
I have a sensor which sends data in a not specific time and each time start to sending data sends more that 100 data in 5 seconds
My problem is i just want one data...
Hello,
as described in the Compatibility Matrix it is necessary to use a revison 3 chip to use the S130 SoftDevice? Right?
Please explain why the Revision 2 chips...
I'm working in a project & I want to wake up the system from the sleep mode but it didn't wake up or I don't know what is expected on the wake up, will the system be run from...
Hello
I am using PCA10028 and I have written some customized service after taking help form nAn36 documents. Now I want to combine the predefined standard services like IMMEDIATE...
Now that the infocenter is available, please consider making product anomaly descriptions available at a permanent URL, e.g. infocenter.nordicsemi.com/.../PAN .
The frameworks...
Hi,
Same question in the ARM forum: topic
I am a (French, sorry for my English) software engineer with very little knowledge in hardware. As part of a prototype, I'd...
