HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi,
So I have seen there is a clean -up option to set the architecture core HW registers to their warm -reset values as specified by the architecture before running the...
Hello everyone,
using Segger Embedded Studio, I encountered an issue with the TWI libraries. My device consists of a custom PCB controlled by the nRF52840 (programmed with...
A simple and maybe trivial question. When in a thread I wait data for example with
is it like call continuously the k_yield()? How the api above works in the underhood...
Hi
is there any example or Tutorial to start from the beginning stage of developing Multiprotocol (BLE and Thread)?
I've tried searching many articles still unable to...
Hi,
Chip: nRF52840
OS: nRF Connect / Zephyr: v2.3.0
Problem: Saving coredumps to external flash
We're trying to add a bunch of debugging features to our firmware before...
I am using the PCA10040 nRF52DK board
I want to connect the UART RX and TX pins of the nRF52832 to my target CPU
I have cut the connections at SB16 and SB14
I can see...
Hi Sir,
As we know, Matter 1.3 supports Electric Vehicle Charging.
Do we have any plan to support the example of Electric Vehicle Charging?
If yes, what is the time...
Hi, We are using a Segger JLINK to program a nrf5340 product using the SWD interface. We have been successfully programming units using a design where there is a 100k pullup...
When we try to test the stability of the UARTE peripheral, we find that when inserting and removing the RX pin, the uarte_handler callback function is very likely to goes...
What is the recommended UART SUSPEND sequence to use the PM_DEVICE_RUNTIME? I am having trouble using the PM capabilities with the UARTe driver. I am developing on the 52833...
Hi,
I am trying the https://github.com/NordicDeveloperAcademy/bt-fund blefund_less1_exer1 using nRF52840 DK. I am able to connect but not able to detect button press. I...
SDK:17.1
application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble I want to know what operations will be performed when...
Hello,
I saw in an old forum thread ( https://devzone.nordicsemi.com/f/nordic-q-a/79412/lwm2m-amount-of-object-instances-limited ) that block transfer was not fully supported...
Hello! I am using nRF52DK and the nRF Connect SDK with Zephyr to create my custom application. For one part, I am recording IMU values at a frequency of up to 200 Hz and loading...
