I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi there,
I must interact with an I2C slave that sends variable-length messages. The first byte of the transactions describes the length of the remaining bytes.
i2c_write_read_cb...
Dear Support,
we would like to know what is the total value of the capacitance and the inductance of the nRF52805 (for ATEX certification). I can not find this information...
We have project using the common Matter Code base from SDK 1.6.1 and using a variation of the code to act as a switch sensor device time. This seems to work pretty well; however...
I need to add tx power to my BLE advertising, but I need to ensure it is in the Scan Response only not the main AD PDU.
Also, I change the Tx power by code using the function...
I have a PCB made for my project. I want to read log from RTT. When I try the same software in the development kit, I can read from RTT. But when I want to read from the PCB...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
Hallo,
In the BSP startup files for the nRF5340 (gcc_startup_nrf5340_application.S & gcc_startup_nrf5340_network.S) the interrupt vectors USPTn_IRQHandler (n=0,...,3) are...
I hope someone can help me here with my question.
In my project we are using a nrf9160 with modem fw version 1.3.5. The application sends/receives data periodically (1 hour...
Hello and thanks for reading.
I have a critical problem with my device, and seeing as the problem is BLE related I figured I would ask your help as well. We are using the...
I'm using an nRF9160-DK board with the provided iBASIS SIM card. I followed the instructions here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.4.0/nrf/working_with_nrf...
Hi, I have a problem related to DFU OTA through BLE
When performing OTA through Bluetooth, I encountered the following issue:
Firmware built in the same build can be successfully...
Hello, I started looking into the DPPI from NRF5340 series and planning to integrate some functionality into an existing zephyr-based project. Specifically, I need timer-based...
Hey team,
We're having trouble with our device. It's been working fine, sending messages to our backend without a hitch. But after a while, it starts having problems connecting...
Hello.
The MCU of our new design will be the nRF52832.
I would like to know if it is ok to read the voltage of the battery that powers the system, nominal voltage of 3...
Dear support team,
1. Can mesh provisioner configure multiple devices at one time? For example, there are five unprovisioned devices within the provisioner's network. Can...
