hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
In the devzone there is a list of the "Recent and unreplied" posts, but is there a way to just browse all the devzone posts? Not just the "Recent and unreplied" list.
I...
I am debugging an issue where my nRF9160 (NCS 2.7.0) rolls back to the previous firmware after a seemingly successful upgrade. I am not getting enough logs from MCUboot to...
I was in the process of evaluating a driver when I noticed I2C communication was not working as expected. I put a probe on the relevant pins and noticed the Voltage on my...
Dear Nordic Specialist,
I would like to ask about the correct usage of the power recommendation parameter in the channel sounding configuration.
In bt_le_cs_set_procedure_parameters_param...
Hi，
Recently, I encountered a problem.
I wanted to set a MAC address of type BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE, with the upper two bits set to 11 as well...
Hi,
I am using nRF9151 with nRF Connect SDK 2.9.0 .
In our project we are using an external NAND flash (MT29F4G01ABAFDWB) over SPI, and it is working successfully. We...
Planning on using the npm2100 PMIC as our PMIC for an upcoming asset tracking solution. We will have an accelerometer that will determine when the main MCU (nrf54) wakes up...
Hello,
I would like to know if it is possible in a Mtter project, to activate or not the MRP messages as mentionned in Matter Core specifications ( chapter 4.12. Message...
NCS 3.02 + nRF54L15
I'm troubleshooting a potential bug. Are these blocking routines, or if not how do I monitor for successful completion of flash write? I looked the the...
I found a issue, I open a sample project " v2.5.0\nrf\sample\cellular\location"
when I click "Add build configuration", no nrf9160 option and only nrf52840 can be selected...
Hi, I am trying to do pwm a rgb led using nrf54l15dk and custom board using nrf54l15 on port1 with pin connections on (p1.10, p1.8 and p1.13 for custom) or on (p1.11, p1.12...
Greetings,
I have worked with the MCUBoot and its Serial Recovery feature with success and recently tried to enable the CONFIG_BOOT_SERIAL_WAIT_FOR_DFU option ( as well...
Hello,
I am intending to extract audio from the onboard microphone of nrf5340-audio-dk.
I used the nrf5340_audio application as reference but cutting off the bluetooth...
Hi,
I'm trying to use same UART channel on both project-specific purpose and MCUmgr DFU. However, when I enable the option CONFIG_MCUMGR_TRANSPORT_UART, the code reset's...
Hi, I used in my hw design Config. 6 for nRF52840 QIAA aQFN73
https://docs.nordicsemi.com/bundle/ps_nrf52840/page/ref_circuitry.html#ariaid-title7
The question is how...
