hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello, Not sure where to direct this (we can open a GitHub issue but wanted to clear it here first), basically everything works great on our Galaxy Tab S6 Lite ( SM-P610)...
Hello,
i am new with the nrf9160, and we are using the download client to download a firmware for a secondary mcu. At the moment its implemented so that at the begin its...
Hello, I recently acquired the thingy53 device and I am trying to use the example of the weather station with matter:
Weather Station . I am following what the documentation...
I've built a simple Matter device for the nRF52840, using the chip-build-nrf-platform Docker image.
The host OS is Linux, and I mapped the physical device ( /dev/ttyACM0...
Dear nordic,
state of your MCUBoot + Immutable bootloader is just awful.
Please fix this hook, when enabled it disables updates of the mcuboot bootloader when used with...
Hi,
From nRF5340 audio example kconfig, there is a note that "now 48kHz is the only sample rate supported". Is this correct? My application would only work for lower bitrate...
Hi,
I have a RIGADO BMD-300 module that can only be accessed over the air. (no physical access)
The modul has the BMDWare ( https://file.elecfans.com/web1/M00/20/D2/oYYBAFmk2JOADMegAAu4fGDEUUo022...
Hello,
I am looking at using the nRF52832 for a safety-related purpose and therefore want to isolate the safety-related code away from the Bluetooth stack. The main concern...
Hi,
I have observed a strange behavior when manually selecting wrong PLMN. I get EMM reject cause 11/PLMN not allowed as expected, but then the modem is stuck in CEREG state...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 Hello. In my project, I want to make sure that my project always works during power on. How can I check if my project can...
I am using a nRF52832 with a LISD3H accelerometer. When I initialize the twi driver, I see a ~250 uA increase in current. I was hoping to initialize the twi driver, enable...
Hello,
I use nRF52832 and SDK 17.02.
I use app_button library to detect and handle button pressing.
Everything works fine except that I have a testcase that is to...
We have a very simple application with an out-of-tree driver that is working fine with NCS 2.0.2.
However, changing to NCS 2.1.0 or 2.1.1 results in a DTS error:
(the...
