hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello DevZone,
I want to transmit some connection information such as a Bluetooth address serially to my peripheral and have it add it to its whitelist.
I have read a...
Hello,
I'm am trying to use the UART0 bus on the network core at the address:
uart0: uart @ 41013000 {
compatible = "nordic,nrf-uarte" ;
reg = < 0x41013000 0x1000...
Hi,
ubuntu 20.3
vscode + nrf connect
when i creat project from sample code unicast_audio_client, i get the following compiling error message:
* Executing task: nRF...
Hey!
I have inherited a project with a nRF9160 + nRF52480 combination to do LTE and BLE communication.
The setup is as follows:
- nRF9160 using BSDlib @ NCS 1.5.0...
My Peripheral device (nrf Connect SDK, nrf52840) will pair using NFC with an Android (8.0.0) phone. But although the Nordic device shows it is connected (in its UART output...
This press release isn't clear on the exact nature of the LwM2M software stack used on the client side. Are we talking about Zephyr' s LwM2M subystem or AVSystem's Anjay ...
Hi, I am working on a pcb design utilising the nrf52840. I want to use a pcb antenna. I am a hobbyist so It’s very likely I’m misunderstanding something. I am interested in...
Hello,
I am using NRF5SDK V5.0.0. For a sample study, I need to use the bootloader. Can I boot over uart when we install mesh_bootloader_serial_armcc_nrf52832_xxAA.hex software...
Hi:
Currently I am testing to upgrade dual core application on nRF5340 DK, NCS version is V2.0.0.
The two core applications are written by myselves, not based on NCS routines...
Hi
using NRF5_SDK 17.0.2
I'm trying to better understand the DFU process, currently have a large number of questions. But mainly i would like to better understand the...
hello
I am watching this video to operate the nRF9160DK. The PIN number was written on the back of the nRF9160, so I skipped the video to 9:36 as instructed at 5:21, selected...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
