Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I am working with NRF52840 where I use the FDS library from the nRF5 SDK, currently SDK v15.3.0.
My issue is that I have seen my hardware suddently halts/hangs due...
Hi Team,
We are using the nrf52840 SOC for our application.Is there any way to reset the BLE stack when it is in hanging state and not able to advertisement or scanning...
Dear Support team,
in 2 different projects I am using the nRF52840-CKAA -D and nRF52840-CKAA -F .
I would like to read out the chip version by command and am trying to...
Hi, I work with a win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk. I am using peripheral_uart exemple, I need to change the connection intervals on this example...
Hi
I try to use in a mesh topology. I decided to send a string from client to nodes and receive its response. but I don't know how apply that. please help me to choose an...
hi , we have a nRF52840 DK when connected to PC via J-link there LED5 blinks . when i try to flash the code using Kiel IDE
get this error
using nRF connect the device...
Hello DevZone,
On my board I have a nRF52810 and a nRF52840. I want to implement a serial bootloader for the nRF52810 and have the nRF52840 program it.
I have looked...
Hello All,
We've got a new design using the nRF9160 - most of the PCBA's are connecting just fine to LTE-M - but I've seen a few with 'erratic' connections to LTE-M - I...
Hi, I can successfully build the openthread-cli sample but fail with all matter samples
Please refer the following log
> Executing task: nRF Connect: Build: light_bulb...
Hi
I'm just starting out to test the nRF9160 DK board and have just flashed the NB-IoT Asset Tracker as per the introductory video uploaded by Nordic here:
https://www...
I use a nRF9160DK for make my experiments:
nRF9160(modem) -> mdm_1.3.2
nRF9160(application) ->Serial Modem LTE (nRF SDK 2.0.0) with UART 2 and CONFIG_SLM_NRF52_DFU_LEGACY...
Dear Support Team，
Based on NCS 1.9.1, compile and download Hello Word firmware to nRF5340-DK (1.0.0), measure the voltage of all IOs with a multimeter as shown below: ...
After I ported my project to ncs2.0.0, I found that the RX of nrf9160 could not receive data. To this end, I modified at_client for testing and found the same phenomenon....
Hi All,
Later I will build a Custom Service, so I refer to ble_app_blinky.
According to the image below, I cannot clearly understand the difference between the two from...
