hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
In the nRF52840, I used the app_usbd_cdc_acm_write(&m_app_cdc_acm,tx_buf,size) method to output the data.
At the beginning, I use the pyserial to read the output data...
Hi,
I'm developing a software in python 3.9.6 64-bit which program a nRF9160 and nRF52840 using pynrfjprog.
The software is working from vscode debug session. But when...
Hi,
We are doing an analysis of power usage using a roaming sim vs home sim since the roaming sim data charges tend to be cheaper. (You wouldn't have happened to have done...
hi,
i m working to create a zigbee network using demo example of light bulb given in sample project of nrf5340dk.
as of now i am able to connect 2-3 bulb devices(i.e....
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
hi team,
working Environment:
nRF 52840 DK, SDK 17.1.0
keil uvision 5 IDE
os: Windows 10 pro
individually, I have worked on USBD and USBD_Audio examples.
now need...
Hi,
I am using an nRF52840 Dongle board and am not seeing any serial output. This is a board and set up I have used previously so I know the hardware is OK. I can download...
software:nrf connect sdk 1.9.1
hardware:nrf5340
hi professor,
I use the nrfx_gpiote_in_init(GPS_TS_PIN, &config_in, gps_timepulse_handler) but return NRFX_ERROR_NO_MEM...
Hello Nordic：
I wanna to know what actions a thread have done from reset to joined a thread network.
I observed the air packets by using Wireshark. I found a router(rx_on_when_idle...
The device is connected to the PC via FTDI chip. The device manager shows the COM port. LTE Link Monitor v2.0.1 cannot find the connected device on SELECT DEVICE. The windows...
Hello.
I am using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral and developing.
I am using nRF Connect to communicate with the peripheral nRF52832.
One of the...
Hi,
I have tried to follow the below tutorial ( https://www.youtube.com/watch?v=hY_tDext6zA&t=933s) . While I am trying to advertise the ble by following that webinar. I...
Hi,
I want to use BLE as both connectable mode and non-connectable mode in the same application. Is it possible to do that?
Is it possible to switch connectable BLE mode...
