Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
project set up: Development board used nrf52832 ,SDK 15.0 ,SEGGER 5.10
actually i want to read data string from ESP32 using nrf52832 via UART (RX,TX) and send it to nrf...
Hello All,
We are using Power Profilier Kit 2 for measuring the current consumption of our device.
We Start the measurement at 14:16 PM. after 1 hour and 39 minutes (at...
HI,
we are working with
nRF5 SDK v15.2.0 ------------------------ Release Date: Week 37, 2018
Our use-case has a central device, which has 7 to 10 peripheral connected...
Hello,
We are using nRF Connect SDK 1.8.0 with nRF52832. As per the nRF Connect Documentation, when there is no active task, idle thread is called. Could you let us know...
Good morning,
I' mi trying to improve power saving on a device and it would be great to trigger:
1.an NRF52832 input pin transition triggers a "SPI1 instance" reading...
Hello,
I want to send 614.4 kHz clock signal to GPIO.
I checked that GPIOTE example could be used for this.
When I update uint32_t cc_value at nrf_drv_timer_extended_compare...
In searching, I haven't been able to find much information on implementing USB CDC ECM. Has anyone successfully implemented CDC-ECM with an nRF52? Alternatively, has anyone...
Dear nRF,
I know this topic has been covered many times, but I am unsure how I can change the uart pins for BLE 2-wire? I have not found any configuration for it inside...
Hi,
We've been in the process of debugging our development board but are having issues. When we try to connect to our board we get:
ERROR: [SeggerBackend] - JLinkARM...
I am using the Segger interface for designing an nRF52 based device. I am planning to use SWDIO SWCLK VTref and GND pins on my device. Is it necessary to connect the nRESET...
Hi!
We upgraded our node version 12.x to v 14.x and are trying to run in on Ubunto. "yarn install" trying to download pc-ble-js driver automaticly from the rebository git...
Hello,
I'm working on getting PSM mode with the Serial LTE Modem on the nRF9160 v1.0.0. The power consumption of the modem (26.4 uA) is too high compared to the documentation...
Hi.
I am using nCS with vscode to develop an application, So far I was only working with peripherals and my build file (.bin) size was about 70kb. Now I want to add BLE...
Hi,
I have a strange question about app_buttons, I have two buttons, only one of the buttons is initialized, which works well, but once both buttons are initialized at the...
