hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
Hello DevZone:
I can see that they are working on a module with WIFI6, my questions are the following.
Will the module have its own evaluation board or will it be integrated...
Very quick question:
I've created a device which implements the Legacy DFU Service. I've also created an Android Application that I plan to develop to be able to conduct...
My application code running on nrf51822 calls sd_ble_gatts_value_set to update a control characteristic. After 16 times receiving NRF_ERROR_BUSY status from this function...
Hi everyone,
first time posting here for me, let me know if i'm doing it wrong.
I'm currently developing a "modem module" built around nrf9160 and working with AWS using...
Hi,
With the NRF Connect SDK version 1.9.1 it is not possible to setup a Thread Coaps connection.
The DTLS handshake fails after Client Hello with an Alert message ...
Hi,
The below is our requirement for NRF5340
1. we have a DFU application with bootloader as an hex file
2. we have another app say blinky as an hex file
3. merge...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
I use the NCS version 1.9.0 with SES.I build and flsah successfully.I use the antenna array with 4x4,about 16 antennas.
In Tx,i use the Putty to debug serial.there is it;s...
Hi,
I have a hardware that I want to connect via BLE and send data via NUS (Nordic UART Service). I can connect to this hardware via the NRF Connect application on android...
