I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hello,
I have a few questions about operation around the nRF9160.
I uploaded a minimal program on the nRF9160-DK card to obtain low consumption.
I get 600uA on average. In...
Hi,
I have implemented the USBD CDC ACM driver into my firmware. What stands out is the latency as soon as the event
APP_USBD_CDC_ACM_USER_EVT_PORT_OPEN triggers, my terminal...
hello. im having issues using ble uart, im planning on connecting my phone to nordic by bluetooth and to pc by usb, the problem that I have is when I use a usb port terminal...
Hi,
We are going through the errata file (nRF52840 rev 2) and wonder how to link anomaly (chip level) with nRF Connect SDK release (RTOS level)...
Where to find the...
Hi!
I am trying to interface LIS3DH module ( https://www.adafruit.com/product/2809 ) with nRF52 DK, SDK 11, via i2c/spi. I tested on Arduino UNO & it gave x,y,z values....
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
Hi,
We want to know more about BLE mesh OTA update in Nordic Connect SDK V1.8
Can you please share detail implementation on Firmware Over the air update in NCS 1.8 ...
This might not be the optimal forum for this question, but I'm not sure where else to post it. I have a (I think) very simple question about configuring Zephyr.
I have a...
Hi!
Currently working on a firmware upgrade of nRF91 ns(non-secure) board and build a smp_svr demo from ncs samples found on ncs\v1.7.0\zephyr\samples\subsys\mgmt\mcumgr...
SDK: NCS 1.7.1.
Based on: Peripheral UART example
Central: nRF Dongle
Peripheral: nRF52832
Hi,
I am running into an issue using the "Just Works" pairing method when...
Hi, I was wondering if there is any way to advertise connectable, but non-scannable advertisements.
My device does not have a scan response, but I still see a lot of scan...
Hello,
There is a small problem that I don't know how to solve. I tried looking for it but to no avail. Essentially, my device which runs on NCS v1.7.0 will stop advertising...
Hello,
I am currently trying to record audio using a PDM microphone on the nrf52840 using the nordic PDM library. I have configured the PDM with the default settings, enabled...
nRF52810 SDKs and SoftDevices compatibility matrix does not list nRF52810 SoC revision 2 in the list of compatible SoC revisions for nRF5 SDK. Revision 2 is listed only in...
Hi
I have a machine MacBook Pro 14 Inch 2021
Chip : Apple M1 Pro
I am using nrf52840DK
Using Segger 5.68. installed via Toolchain
Using sdk connect 1.8
The J-Link...
