Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I have nCS installed and when creating a project in nCS installation directory (default path), then i have option to choose "Configure nRF Connect SDK Project" from...
Hello,
For my board i would like to remap uart to pin on GPIO PORT 1.
Current:
&uart0 { status = "okay"; current-speed = <115200>; tx-pin = <20>; rx-pin = <22>; rts...
Hi,
We have a requirement to connect a SPI device to each SPI interface present on nRF52840, and we want to write to those multiple devices in parallel. Is there any API...
Hello everyone,
I would like to run the ANT examples "ant continuous scanning controller" and "ant scan and forward" on my nRF52840DK(PCA10056) boards however it only supports...
Hi,
We have a device based on nrf_52840, SoftDevice_132_3.0.0 and SDK_12.3.0, using BLE for communicating to a PhoneApp and UART for communicating to a washing machine...
I'm writing an application for the nrf5340 with nrfConnect v1.6.1,
I've been able to do the FOTA upgrade through BLE with the example smp_srv located inside zephyr/samples...
I recently got the nRF52840DK and have been able to build/flash a couple simple samples. However when attempting to try the OpenThread CLI example on tool chain v1.6.1 and...
Hi,
cannot run pc-nrfconnect-launcher v3.7.1, built from sources.
```
$node -v
v12.22.5
$git clone https://github.com/NordicSemiconductor/pc-nrfconnect-launcher...
Hi,
When I want use nrfjprog to program my NRF52, I have a problem.
This why I write to program my nerf : nrfjprog -f nrf52 --program _build/astronaut.hex --sectorerase...
Hello,
Is there example code on how to get NRF_SAADC_INPUT_VDDHDIV5 working? When I do nrfx_saadc_init(), I get NRF_ERROR_INVALID_STATE.
Same code works fine with normal...
I am using nrf5340 and icm20948 for our development. i had initialized things as shown in code attached.
this work fine for me. but when i am uncommenting rc |= inv_icm20948_enable_sensor...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
Hello,
I've been very slowly gearing up towards developing for the nRF9160. I'm going through the "nRF Connect SDK Tutorial"
https://devzone.nordicsemi.com/nordic/cellular...
