hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Trying to compile samples/net/wifi/ to test the esp8266 with Nrf52. we have our custom board. but Im' testing using Nrf52840 DK now.
I've this file
in myProject/boards...
We have a custom PCB with GPS circuit copied from the NR9160-dk board.
The default GPS example is working fine. However, we want to combine GPS tracking and LTE-M connection...
Hello,
I am using NCS 1.5.0 and modem firmware 1.2.3.
I have nRF9160 DK version 1.0.0.
I am trying to run "full_modem_update" example firmware on this.
But getting...
HI
I use NRF9160 serial_lte_modem to test NBIOT/MQTT, current SDK is V1.6.0 ,and config mqtt keepalive =1200S.
after 9160 connect net, control mqtt connect my mqtt server...
I have connected 3 Peripheral using Name Filters and 1 central.
I am able to connect and communicate with all correctly.
But I need to identify that conn_handle 0x0 ,...
Hello!
When collecting dc1.4v with SAADC, there is an error of 100uv. SAADC is configured in differential mode, with N-terminal connected to GND and p-terminal connected...
Hi,
I've read in these forums and seen the machine instructions within the C code that nrf_delay_us (which BTW is used to do nrf_delay_ms) is implemented by executing a...
Hi team,
I would like to know the default channel used for data transmission and the frequency of the channel.
Also whether the frequency is configured in the softdevice...
What is the purpose of the external capacitors on DECA and DECN? DECA calls for 1uF and DECN calls for 0.1uF. The datasheet calls these out as "Regulator Supply Decoupling...
Hello,
sorry to border you again, but I have a problem that block me for many days. I read all nordic questions on TWI (I2C) but did not found a solution... :(
I have...
Hi,
We are designing a custom Board using nRF52840 SOC.
We are operating it in Normal mode, using an internal DCDC converter
We have used configuration 5 from the...
Hi there,
I need to transmit 33995520 bytes from nrf52 peripheral device to a Windows/Android device. Currently it takes about 13 to 14 minutes to complete the data transfer...
the flash of the nrf52832-QFAB is 256KB. the softdevice S132 is used which consumes 152KB and the compiled file of the BLE_UART only consumes 98KB (after making the changes...
