hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
Hi All,
I'm trying to interface a SD Card with nRF52840 DK.
I've got a SD Card socket and a FAT32 formatted 8GB sd card.
When I run, fatfs example , I get following...
hello,
i am using nrf52840 in our customised board with sdk 15.2 and trying to achieve long range with coded phy using long range demo example as base now i could be able...
Hi,
I have two boards NRF52840 DK and I wanted to use example for BLE Central&Peripheral NRF Relay. I have just run example with Heart Rate peripheral and I can see that...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
