hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I updated my Power Profiler software on the NRF Connect Desktop software.
Immediately after switching to the new GUI, I noticed a significant change in power performance...
I am trying to use the NRFX_WDT design in SDK 16.0.0 on a board using the nRF52832.
In the file nrfx_wdt.c, the allocation index is declared/defined as:
static uint8_t...
The drop down does not list the nrf5340dk.
Using nRF Connect Toolchain Manager I open a command prompt in the v1.5.0 sdk,
cd zephyr\samples\drivers\spi_flash
I did:...
Hello,
I have a project based on Cloud Client v1.4.0 using AWS IoT cloud as the backend. I have made some changes in the code so that I disconnect after sending some values...
The frequency tolerance for ANT stack for an external 32.768 kHz crystal oscillator should be +/- 50 ppm max.
Does it mean over temperature range?
There was the same question...
HI:
Now i am use the OTS to transmit image, if we want to set the MTU=185, how many paramter must config here?
example:
CONFIG_BT_CTLR_TX_BUFFER_SIZE=185 CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hello, I have created my own C program (in eclipse) that basically should just initialize to an LTE network and connect to it, nothing fancy at this point.
I have come across...
Hi, I tried to set up the environment for the nRF Connect SDK v1.5.0 using nRF Connect for Desktop on Ubuntu 18.04.
In step 2 (Cloning the SDK), I got some errors while...
I use arduino to program a nRF52832 board. I had problems to move a running project with a ST7789 SPI display to the nRF52832. I use the Adafruit lib to drive the display...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
