Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
To setup the UARTE for use in Zephyr I've configured a nrf52840dk_nrf52840.overlay as Zephyr documentation suggests:
& uart1 {
compatible = "nordic,nrf-uarte"...
Hi, I'm setting up a timer to invoke (via PPI) the ADC in scan mode. It'll read to channels with MAXCNT of 10,000. The ADC built in timer has a value from
[80..2047...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
Hi everyone,
I wanted to make reset pin funtional on nRF52 DK while using pca10040e folder so that I could develop on nRF52810 later, but the reset button did not work as...
I've noticed the idle current of my application changes permanently by ~5uA after using the radio, timer2, and/or the app timer (not sure which). I'm using a custom radio...
Hello,
I am using libUARTE and libUARTE ASYNC for reliable communication over UART.
I need to transmit data that is stored in read only memory but this module seems to...
Hi,
I'm trying to use flash FDS on 10040-Dk with softdevice s132 and freeRTOS.
I debug the code using segger embedded studio, when executing a write to the flash It reaches...
Hello,
we want to support scan for both 1Mbps and Long Range beacons and we are using the S140 6.1.0.
This is the configuration for the scan parameters:
When this...
Hi all,
DFU package V1_0_75 was developed using SDK12 for nrf5232 and V2_0_45 was developed using SDK16 for nrf5232.
I am trying to update from V1_0_75 to V2_0_45 using...
HI
describe my device first:
A Temperature and Humidity Sensor(twi) measure every second
nrf52832 module
it has an lcd and its control IC(twi),
a spi flash to store...
