We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
in sdk16 "examples\peripheral\usbd_hid_composite" example, i found that after those code
ret = nrf_drv_clock_init(); APP_ERROR_CHECK(ret);
nrf_drv_clock_lfclk_request...
Hi,
I want to set advertising name in the main.c.
err = bt_set_name("NAME test"); if (err) { printk("BLE set name error (err %d)\n", err); }else{ printk("BLE set name...
Hello Nordic,
I had some questions regarding the management of versions of various components during application development (nRF Connect SDK/9160 Modem Firmware/Modem Certifications...
1. I am using a boost to power the USBD since I am using coin cell to power the whole system, what minimum and maximum supply current is needed/can be handled?
2. What boost...
I have being confused by other post around DevZone about DS18B20 to integrate with nRF BLE application or rather programmatic aspect is concerned . Is DS18B20 suitable for...
Hi!
I've just received a nRF9160 DK.
I've installed nRF Connect v2.6.2 and LTE Link Monitor.
I select the device (3 serial ports are shown). I press reset button and...
When working with a custom board with nRF52840 chip, I'm having serious problems with SWD connectivity. In many cases JLinkExe can't connect to target at all. I did some measurements...
Hi there!
I'm trying to simulate a peripheral with a PCA10040 and nRF Connect for Desktop.
I've made the Server Setup, applied to the board and started advertising - everything...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Initially I was in assumption that once...
Hi,
Is there a table / .xls available for ALL nordic parts to date?
I'm trying to find all options with +8 dBm TX Power & WLCSP package. (no need for usb)
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
