Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
Is it possible to get access to the information contained on the SIB (System Information Block) in the nrf9160? if yes, is it through the nRF Connect v3.3.0?
Thanks...
I want to get the 128 characteristic UUID of the peer device during the connection phase. Now I use SDK is 15.3, the softdevice is 6.1, and only 16-bit UUIDs are obtained...
I have the NRF52 DK, I run make flash in the UART example, everything works. I'm able to run the loopback test.
I navigate to the serial port example, make flash, nothing...
Hi Everyone,
I would like to understand how the multi peripheral application works in this given scenario:
Scenario:
Considering one peripheral (P) is connected to 4...
Hello,
I have been working with NRF 52840 DK and finally able to make the advertising work on PHY CODED but I was required to use extended packets.
My question is
Is...
Hi i am using sdk15.3 secure boot-loader example. i had change backend to cc310. without optimization i am able to upgrade code but when i am using optimization level 0 it...
Hi,
I am working on an USB CDC program with nrf52840-mdk-usb-dongle. The PC needs to use a terminal emulator like putty to connect to the dongle. Now I send and recieve...
I use Zigbee CLI example on nRF52840. (examples\zigbee\experimental\cli\cli_agent_router)
It use UART as 115200 bps with CTS/RTS (hardware flow control).
I want to change...
Our product uses non-connectable/undirected advertising, where advertisement packets are sent every 1 minute for 500ms time. For that we are using FreeRTOS timers to start...
1: Is there any information that can be systematically introduced to the production test of Bluetooth products? 2: What parameters do I need to test for mass production of...
Apparently, Config AppKey Update message can be transmitted in the key refresh procedure. However, one point let me very confused, I looked into the Mesh Spec v1.0.1 (page...
Hello. Is it possible for a central device to retrieve the BDADDR( 6 byte array data ) of a past peripheral device by using the peer manager? ("past peripheral device" refers...
Does anyone know how the raw data message is structured to enable GATT Proxy? Here is a screenshot from the app. I know one byte is used to indicate whether to enable or disable...
Hi,
actually I developed a system based on an nRF24AP2 able to read data coming from different HRM ANT+ sensors and transmit them via WiFi using ESP8266 that is acting as...
I have clock drift issue, should I calibrate anything? I test this simple code to get 1second or 100ms signal both of them are inaccurate.
here is my code for 100ms; I tested...