I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello everybody, I am trying to exercise the DFU for mesh following the DFU quick start guide (v2.0.1). To put you in context I have four nRF52840 devkits, three of them are...
hi..
i am using nf52832 ... segger 15.2version ... while i am start to execute the code .. i am getting the error at nrf_breakpoint_cond ... then i tried to set breakpoints...
Hi,
I am new to software development and had a query about software version control with the Keil IDE using git.
As a beginner, I simply copied an example project in the...
Hello,
I'm on nrf52DK PCA10040, SDK15.2
I'm sure it's quite basic, but I don't get it. I just need to write actually two uint32_t value in flash memory (so FLASH_DATA_LENGHT...
Hi,
I have got a nRF542840 dongle, and I have installed all the required programs (I got all from this website: https://www.nordicsemi.com/eng/Products/Getting-started-with...
I recently went through the process of building the pc-ble-driver-py library/drivers and running it on my NRF528240 Dongle and have no issues with it. I wanted to share it...
Hello,
I have problems to get SES working with nrf51822 projects. If i import project with help of tutorial from nordic semi i get undefined symbol __data_start__. Now i...
Good day!
Work with nrf51822 central with S130,
I've read this questions and links in answers:
https://devzone.nordicsemi.com/f/nordic-q-a/20924/sd_ble_gattc_char_value_by_uuid_read...
My application is based on one of the example projects and runs on the nRF DK. Next step is to port this application to a custom board. Are there any guides written on this...
below is a little part of code I copy from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi
I need a CLI over RTT on an existing project. I believe that I have extracted all the required bits from the CLI example. I dont need history, UART, USB or anything else...
I am using NRF52832, twi_sensor_pca10040 example with SHT3X sensor.
I changed slave address to 0X44 and SCL, SDA pin to 27 and 26. TWI TX transfer work fine, in response...
using nRF-Sniffer-v2 at 52832 sniffer, I can get advertising packet. When select device form drop-down list, & connect the device the sniffer can't get any packet. Any one...
