I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hellou, I'm developing firware which is modification of light switch example. I have build in communication protocol, and when i receive coomand to remove nodes promisioned...
I recently downloaded nRF52840_PS_v1.0 and noticed a change in the register description for the SAADC RESULT.PTR (p. 365). A note was added that states... "Only bits 29 and...
Hi,
I have got two questions:
1) I am trying to write a code into nrf52840, and was wondering is there a specific SDK version to be used for the nrf52840 DK, or we can...
Hi,
I have used Nordik UART iPhone App code for our App development
Now till iPhone 7 App is working fine.
Now when I run App on iPhone X it is displaying log error...
I have a usb dongle with nRF51422 (PCA10031) and downloaded nrf sniffer software version 2-beta from https://www.nordicsemi.com/eng/nordic/download_resource/65225/1/90637756...
hi,
i am using NRF52832 DK, and sdk 15.0.0.0 ,,
i want make the central to work also as a peripheral...i.e whenever central is not working ,or ,central is not in connection...
I am evaluating the throughput of BLE communication between 2 NRF52832's, 1 acting as a central and 1 as a peripheral. I've modified the ATT_MTU Throughput Example, and I...
Gone through sdk 11.0.0 Experimental_ble_blinky application, i trying to assign one gpio pin in place of connected LED. what is it receiving when pressing on & off switch...
Hi,
I'm working with nRF52832 chip following the example "ble_app_beacon". I see the advertising packet is limited to 31 bytes only. However, I'd like to take an advantage...
Hi,
I have arm based application processor and need to connect with nRF52840 using UART, I don't have any idea about bootloader and factory firmware when hardware assemble...
We are trying to determine the emission designator for the nRF52832, or at least to determine the necessary bandwidth so that we can create the emissions designator. Please...
Hi everyone,
I have a problem with SOME android devices.
In particular Android devices with BLE 4.0 & 4.1, but I have NO problem with Android device with BLE 4.2 and iOS...
Hello,
We are using nRF52832 DK with SES IDE and latest SDK 15.0 sd 132. We have developed one multiplink central device and modified ble_nus_c with our application to connect...
I use nRF52832,is 2.5v power supply,but you can't download the program,w hen I set the voltage above 2.8v, I can download the program,then I switched the voltage to 2.5v and...
Hi everyone
I am able to send the data over the UART to the Real Terminal and also to my other device working on UART protocol. However , I am not able to read the data...
