I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am using nus service to send and receive data between Android App.
After connection established, App send some data to my module and ble_evt_handler get that data...
Hi,
I am using SDK 15.2.0 in nrf52840, pca10056 and s140. I want to combine two codes of SAADC and ble_app_uart. I have added every driver files and path for these files...
Hi, I started a 4 layers PCB design in cad-soft Eagle. In nrf52840 ref design they are using blind vias in 1 to 2 layer, so I'm guessing below DRC layer setup is correct for...
Dear Nordic,
I want to test BLE Mesh network. for that one board(nrf52832 DK board is programmed with client example. when i debug the program its entered into app_weak_errors...
Hi
I am using nrf51822 , sdk version 11 and softdevice version 130
In project I am trying to disable SPI1 and TWI0 channel by using following command
NRF_TWI0->ENABLE...
Hi, I are using BT832 module based on NRF52832-QFAA IC in an application. Please provide the following details regarding ble transmission of NRF52832-QFAA-R7 IC
1) modulation...
Hello,
I´ve got a corrdinator, which establishes my network. Also I´ve got an End-Device that joins the network successfully.
Is there any chance for me to observe the...
Hi Nordic,
I am working on a project where I connect via nrf52 DK, to a peripheral. I am runinng on SDK15, with the experimental build ble_app_interactive, inside the ble_central_and_peripheral...
I'm using nRF52832 with SDK 15.0 and Softdevice S132. Within ble_dfu.c anytime a connection is established the on_connect function blindly sets m_dfu.conn_handle = p_ble_evt...
hello nordic ,
i want to download the mesh SDK 2.1.1 to use the light switch example to transform the model simple onoff from sending uint8_t to string ,
i have started...
Hello, I'm using softdevice 6.0 and SDK 15.
In my application, I would like stop the SAADC at the disconnection and then restart SAADC at the connection to power saving...
hi..........
i am using nrf42840 ...segger 15.2 version
i am facing the problem in sleep mode
i used the command to sleep
static void power_manage( void ) { ret_code_t...
Hi guys,
I am currently using nrf51822 with SDK 11. I use Peer Manage to deal with paring and bonding encryption in BLE connection.
Please correct me if I am wrong but...
Hi,
When I'm trying the throughput on nRF52840 with SDK v14.2, I set up a 52840PDK as a 'repeater'; in which case the 'repeater' will receive the output (20kBytes in total...
