I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hello Team, We are currently working on a new project that incorporates geofencing functionality using BLE. We have checked the current consumption in nRF52833 DK using the...
hi professor，
I'm using nrf5340 to design project,now I wan to reduce power consumption to uA level.According to https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hello, I am writing an AT command response parser for my custom AT commands. I thought about using nordic's parser utils found in include/modem/at_params.h but I have been...
Hi all !
I'm writing this message because I'm having problems trying to increase the number of devices in PAwR (I use Coded PHY).
I based my development on the SDK 2.8...
hello . i tested the sample for the persistance key it worked with the AES key . But when i tried with the EDDSA key i received that error psa_generate_key failed! (Error...
I have 7 GB large .ppk2 file exported by Power Profiler v4.2.1. I am looking for a glitch in power consumption. Doing this manually by scrolling through the waveform in Power...
HI! I am trying to decrease the memory use of my application that is built for a nrf9160 and noticed that tfm creates a 256kB partition that it only uses around 99kB of. RIght...
nRF54L15 has RRAM with error correction codes (ECC) built in, with autocorrection.
I guess ECC errors could either happen due to a power loss during a write (when reading...
i am working with the nrf7002+nrf5340 ns when i run the excercise solution and press the button a couple of times, i get this error *** Booting nRF Connect SDK v3.5.99-ncs1...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
I plan to use an ESB as a low latency and high speed protocol.
However, there must be multiple hosts on one network.
Hosts or devices must be able to communicate with...
Hi,
I have a design which mostly follows the reference designs.
I've added a Resistor Network R16/17/24 to allow a UFL connector to connect to the ANT and isolate...
Hello, I really need some help to connect a central nRF52 DK board to a peripheral that was provided to me. This peripheral can connect to a smartphone using nRF Connect and...
NCS 2.7 with Toolchain 2.7
Launch build from Visual Studio
Sysbuild with mcuboot and custom application, custom board
Although the application itself updates when VERSION...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
