Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I'm trying to programm the NRF52833-B-QIAA off board using an Elnec programmer model BeeProg2, but as the revision B of this MCU comes from the factore with APROTECT ENABLE...
Hello, is it possible to reset the battery evaluation using SW without restarting the resources? Unfortunately, I sometimes have to take power directly from the battery, so...
Hello.
Previously, npm1100ic was used. In the npm1100, D+ and D- pins were in ic for usb communication. I don't think there is one in the npm1300. In this case, unlike npm1100...
I am running CoAP client with DTLS enabled on an nRF9161dk.
I poll socket using this code:
I am able to receive data (POLLIN), but when server closes session and sends...
Hi, I am using a module named MS12SF1 (nrf5340 + nrf7002). I was trying to write the Mac address for one time programming by using radio_test sample code. Before doing this...
Hi devzone, I am trying to use the Edge Impulse integration on a Seeed Studio Xiao BLE Sense (nrf52840 based). When I manually download the zip file from Edge Impulse and...
Hi,
I have a project which has been working fine but since adding some date/time functionality, when I enable MCU_BOOT, I get linker errors that I can't seem to get to the...
Hi all,
I'm developing a multilink system with 52840 dongle as central and 8 52832 devices as peripherals, which is similar to previous project in thread part I & Part II...
Hello,
As mentioned in the title, I am trying to use 4 pairs of I2C on nRF5340. Each of the four I2C pairs will be connected to a TCA9548A (I2C MUX), but that is not important...
I want to try out remote mesh provisioning.
I have added a mesh device with Remote Provisioning Server model to my mesh network with nRF Mesh app as the provisioner.
But...
Hello,
I've been trying to setup the nRF connect & power profiler on some of my co-worker, but downloading the pc-nrfconnect addon was not possible via nRF connect, so I...
i used my j-link to flash to my thingy91 nrf52 and nrf91.
now i want to flash a new program using the usb, but nrf programmer doesnt recognize a device when i use a USB...
Hi, I'm trying to send 64-byte reports for INPUT and OUTPUT: 1 byte for report ID and 63 bytes of data. However, the HID service code doesn't seem to handle incoming OUTPUT...
