Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi,
NCS v3.4.0, based on bluetooth mesh light_ctrl sample
nRF54L15-DK
I want to use P1.06, P1.07 and P1.14 as GPIO to toggle waveform, so I modify light_ctrl sample...
I am trying to get a Holyiot 21017 dongle to work correctly as a Thread RCP. The Holyiot 21017 has a nRF52840 and a RFX2401c power amplifier. In VS Code with the nRF Connect...
I am working on a BLE project on the nRF54L15, and I need to add the FOTA over BLE bootloader to it for cpuapp_ns.
I am using NCS v3.4.0 which no longer uses the Sysbuild...
Hi everyone,
We are a research group at a university, working on indoor positioning systems based on Bluetooth Low Energy (BLE) technology. We are currently evaluating different...
For just a first test board off of Thingy 91x design, can nRF5340-CMAA be replaced with nRF5340-CLAA? What's the downside of doing that? Documentation says it's not recommended...
Hi,
I have a question regarding the transmission duration in the Online Power Profiler for BLE (OPP). More precisely, it is about the transmission duration during a connection...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is there a sample project for the nrf54LM20A DK that uses the nrf_802154_radio_driver? We need to implement a custom protocol to work with existing products.
Thanks,
...
My VSC install is up to date, no updates pending in the Extensions manager etc.\
When building an app for nRF54L15DK I get a warning about the SDK being out of date, and...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
