I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
I am trying to build an application that can switch into MCUBoot's serial recovery mode and receive a new firmware image over the serial port. I'm using NCS 1.7.1 through...
I'm using the nrf9160dk (ns). I started an application based on the SIMPLE_MQTT sample. At first, every this worked. I added my one MQTT client with a different set of buffers...
Hi,
The LE Secure Connections Multirole Example is automatically requesting a pairing/bonding.
Why is it not first just doing a connection and requesting the numeric comparison...
I cannot locate an app in nrf connect for the desktop. What can have contributed to this? Can it have a relationship to the network?
Thank you for your help.
I'm doing some experiments with the nRF52840 and SEGGER Embedded Studio. I'm quite new to C but managed to get desired results using and changing the examples. I'm now trying...
Unable to configure hCI Uart project in Segger Embedded
I need to configure the HCI_UART project to support DTM testing, but I cannot enable the configuration parameters...
Hi
We are a group of students working with the nRF9160dk.
We want to try connecting the nRF9160dk to google cloud and send data through MQTT.
We have tried to follow...
Hi,
We want to build PCB using nRF52840. Previously we were using this package but it is out of stock. I want to ask can we use this instead of the previous package. Are...
