HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
I am currently working on interfacing an external flash memory IC (Winbond W25FV series) with the Nordic nRF52832 on my custom board , using the nRF Connect SDK .
However...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hello,
we are testing software with the nRF54L15 DK with the 3.0.2 SDK and toolchain.
When creating a board configuration we use:
nrf54l15dk/nrf54l15/cpuapp
optimize...
I have a project that has been deployed for a few years, which we regularly update via DFU in BLE.
On this project, I had to increase NRF_SDH_BLE_TOTAL_LINK_COUNT.
This...
