I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I have some issues sending valid information to nRF Connect app by bluetooth using the Aduino Nano 33 BLE with nRF52840 on it. I am using Arduino IDE and the ArduinoBLE...
Hi all,
The project I am working on consists of a BLE peripheral, a BLE central and an enhanced shockburst device. I run into a problem in the code of the peripheral:...
In a project based on Softdevice S132 7.0.1 employing the Softdevice timeslot API, I noticed that the nrf_radio_signal_callback_t function passed into sd_radio_session_open...
Hello,
I am using UART_1 to receive GNSS data. For UART_1, baud rate is 115200bps. On terminal, I can see the correct data when baud rate is set to 115200bps. When the baudrate...
Hi, i am using nrf52840 development kit , four servo motor . using 15.2 sdk version
here i am controlling the angle using adc values , i am done with one servo motor . pwm...
Hi
I am modifying the scanning and advertising paremeters for coded (125kbps).
I made the following changes in advertising
.primary_phy =BLE_GAP_PHY_CODED, instead of...
Hi All,
I am using nRF52832 SOC for my development. I would like to buy a packet sniffer for my BLE development.
Can someone please suggest a suitable device for this...
Hi
In the SDK, Replay_Cache_Entries is assigned a value of 40, which means that Replay_Cache can only process 40 unicast messages. That limits the maximum number of unicast...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
Device has both Central & peripheral functions.
It takes about...
Hi,
I used(SoftDevice 140, based on the ..RF5_SDK_15\examples\ble_peripheral\ble_app_beacon )
m_adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
Hello Everybody,
Here are two patches for nRF5_SDK_15.3.0_59ac345 to make the ble_app_uart compile as a C++ application with GNU Tools ARM Embedded 8 2018-q4-major.
nrf...
We are currently experiencing a problem during development of Medical device.
We are currently using nRF52832 on Thingy52 prior to bring up on the product board having nRF52840...
Hi!
I am trying to send over SAADC data from a peripheral device over BLE to a central device. Currectly I have sucsessfully merged the SAADC and BLE_UART peripheral example...
