hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
Hi,
I'm trying to implement Install Codes on our project without good results: The end device could not join the coordinator network after retrying several times.
Because...
Hi All,
I need to send HCI commands from my uC to nRF52840 (with DTM firmware) via UART to for example set channel, Tx power, packet type etc.
Are there any examples/documentation...
Hello,
nRF52832 BLE project using SDK 15.3.0 and SoftDevice 112 v6.1.1. Circuit has the output of a comparator connected to two GPIO pins (COMPARATOR_PIN1, COMPARATOR_PIN2...
Hey guys, I'm currently working with NRF9160, developing code that requires a work-item to be scheduled within a time-frame (timeout value) that could go up to >24-hrs. I...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...
Hello,
I am using nRF52840-pdk with Keil5 and nRF-go studio for development purpose.
I am facing an issue that after new firmware version upload from nRF-go studio to...
Hi everyone,
Currently, I was developing an application on top of Zephyr. I notice that NRF52 SDK provides library for MQTT-SN protocol. However, my application needs to...
Can the TCLK timeout be changed? I have a ZigBee device that joins and performs a key exchange but then is forced to leave the network 12 seconds later due to a TCLK timeout...
I am working on a project that I need to scan bluetooth devices. I am using nrf52832 as a central, sdk 15.2 and s132 v6.1.1. when I activate the advertiser tab on nrf connect...
Hi,
I haven't ran the FOTA download library in a while and I was just testing it. I don't seem to be getting any of the FOTA_DOWNLOAD_EVT events. I am running nRF SDK v1...
I am using nrf52832 as my cnetral and also nrf52832 as my peripheral . i am connected central with peeripheral using ble multilink example code. but it shows only 16bit uuid...
I am using nRF 9160 mqtt_simple example to connect to a custom mqtt broker address as shown below
The following is the mqtt.fx application
I changed all the necessary...
