I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I'm having trouble getting the Bluetooth Low Energy desktop library ( https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.1 ) set up on my Mac. My problem is occurring...
I would like to know what is the maximum ADC sampling frequency for transmitting data over Bluetooth to PC.
I am using two modules having an nRF52832 for each module....
Hello, I think there is an error in ble_advertising.c (SDK 15+).
Line 608, the code is trying to set the secondary phy but checks if the primary phy is valid ( ble_adv_primary_phy...
Hello,
I am very new to evaluating the nrf52-dk board, so I hope this is not too much of a trivial question.
I was trying to enable logging via UART without having to...
Hi
Currently I have a firmware based on template project for nrf52 (sdk15). I am interested in broadcast data, hence I used ble_advertising_advdata_update() in order to...
Hello! I use a 32kHz quartz resonator and I want to interrupt the program after 1 second with a watchdog timer. But when writing to it, 128 I get not 1 but 1.25 seconds. What...
Hello,
I followed the getting started guide but the kit can't connect. I'm getting this error:
net_if.net_if_init: There is no network interface to work with!
Is this...
Hi there,
I have a question NRF52840_PCA10056 and its SDK is latest nRF5 SDK.
The scenario is below:
The NRF52840_PCA10056 build a connection with a smartphone like...
1. It is understood that zigbee3.0 certification requires Green Power, but I did not see the definition and use of Green Power in the example. How does the nordic zigbee pass...
Hello Everyone,
I am trying to compile zigbee_light_coordinator example. I have my path included as ../../../../../../../external/nRF-IEEE-802.15.4-radio-driver/src in make...
Hello,
I have accidential removed the DFU bootloader on my PCA10059 dongel..... is there an image that I can write to the dongle to get it back into its out of the box condition...
Hi there, I have set my SAADC to have an acquisition time of 3us , however when I toggle a pin before and after calling
nrfx_saadc_sample_convert
I measure the time of...
The sample project is "nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\experimental\ble_nfc_pairing_reference"
I think "micro_ecc" is a normal build.
Please check attached...
Hi,
Using the Secure DFU from SDK 14.2 I managed to integrate the NUS peripheral example to have access to an UART pipe in parallel to the DFU when running the boot loader...
