hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
Iam trying to implement multirole ble in nrf5340 using ncs. I am using legacy advertizing type for advertize and observing both.
why it is working only first time...
Hi nRF support team,
In my application, I need to show system date and time, so I am trying to get the system epoch time by using the nRF Connect SDK on nRF52840 dev kit...
Since I am a beginner with Zigbee, I would appreciate your guidance.
Currently, I am using the nRF Connect SDK v2.8.0(Zigbee-addon) with the nRF54L15 to work with Zigbee...
Hi there. I'm attempting to do trilateration between 3 nRF Devices. A1, A2, and A3.
A1 - A2 I can get using the nRF Distance Measurement toolbox
A1 - A3 I can get using...
We have implemented a simple contact switch using the nrf52840 and the latest zip generator (v99). The device connects to a Samsung Smart things edge router. A contact device...
Hello Nordic Team,
HW: nRF52840DK
SDK: ncs v2.8.0
App: hci_pwr_ctrl
I am testing with hci_pwr_ctrl example to see how tx power can be set from application.
The...
I am working my way through the Beginner course on Dev Academy, and am trying my hand at using my own accelerometer breakout board communicating over I2C for lesson 6.
I...
Hi,
I have used course's example for GPIO interrupt for toggling LED and used to update BLE adv parameters without using DK buttons library. But, as soon as, I update BLE...
Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
Hi All
Hi, I am using nrf51822 controller in my design for with SMD chip antenna for RF output.
Can anyone suggest me any reference design(Hardware and Layout files) to...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
Hi,
"In a BLE Mesh network, if a client uses GAP attributes to send data, can it also use the GATT profile to communicate with a single device? For example, can the client...
I am currently using SDK 17.1.0 to implement dual UART mode on the nRF52833. UART0 is used for logging, and it directly utilizes the SDK library without any modifications...
