Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Hi dear, I'm make the tests with send and receive informations using the code base mesh. I need help to better understand the transport of this data
Initially I set my...
I am currently working on LE Audio broadcasting. The system operates successfully on 1M PHY, but I would like to use it to function on CODED PHY as well.
Both the receiver...
We use the https://api.nrfcloud.com/v1#tag/IP-Devices/operation/OnboardDevices endpoint to create and onboard new devices.
Recently, with no changes to code or certificates...
Some questions during the development of a DF project using the nRF52833DK:
Will excessive serial output affect the performance of the microcontroller? For example,...
Hello,
On my custom board, after upgrading from NCS version 2.5.1 to 2.6.1, BLE stopped working.
I get immediately the following trace after calling bt_enable(NULL)
...
I'm migrating from ncs v2.3.0 to ncs 2.6.1 in order to have the ram retetion working with the mcu boot.
But after some modification on my board file using a nrf5340 I get...
I have a custom board file which is based on nrf9160, I want to use it using the west build command and later flash it. I tried the steps under this tutorial: Nordic academy...
Just upgraded to NRF v 2.6.0 (Mac OS; VS Code). Our code previous built and ran successfully on our custom board with v 2.5.0 of the SDK.
Now we get the following error...
Hi all,
I'm developing a project on top of nRF5340. Thus I created a custom board definition in my project area:
That is a direct copy of ncs/zephyr/boards/arm/nrf5340dk_nrf5340...
Hello,
we are trying to use the nRF9160 as a serial modem for a Raspberry Pi running on Debian.
The application is basically the nRF sample "nrf\samples\cellular\modem_shell...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
