We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hello,
I've started to develop with the nRF Connect VSCode extension and enjoying it a lot. However, I've noticed when I share a project the build configuration doesn...
Hi,
I observed what appears to be the same issue as https://devzone.nordicsemi.com/f/nordic-q-a/51337/nrf9160-infinite-nrf_connect-blocking-behavior-post-lte-psm-wakeup...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
