hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
Hello,
I will explain my setup:
I have 2 nRF51-DK each one of them connected via I2C and SPI to two different custom boards. One being the central(nrfA) and the other...
Setup: DK #1 is running native S110/SDK10/nRF51, one service 128-bit w/ 16-bit char:
Service UUID: 0x0xb1ad
Service UUID type: 0x0x2
Service handle: 0x0x0c
Service handle...
I found a discrepancy between a tutorial and an application note.
Step 2.A of "BLE Characteristics, a beginner's tutorial" devzone.nordicsemi.com/.../ calls sd_ble_uuid_vs_add...
Hi,
I tried to familiarise with eclipse environment and i have some problems :
The debug and run button. I searched on google but i didnt found anwser.
How can i define...
I find example : nRF51_SDK_7.0.0_2ab6a52\examples\properitary_rf\esb\esb_ptx_prx .
question 1: can i add this example into my project that build on SDK v610 and it run...
Hello,
I have an problem with DFU on nRF 52 I have followed this thread devzone.nordicsemi.com/.../ but failing to upload firmware.
I have attached screen shot. You...
Hi
I have noticed that the moment I start SAADC task ("nrf_saadc_task_trigger(NRF_SAADC_TASK_START);"), my CPU current consumption rises by 2 mA!
(tested with chip version...
Hello..
I am Using The Balun having Digikey Part No.2450BM14E0003T And Antenna Part No is . 2450AT18B100E
Then it it is Necessary to add Pi network for matching antenna...
I am working on a school project using the NRF51822 with SoftDevice 130 on a custom board and I aim to create an HID gamepad. I am working on my power supply circuit and my...
Hi,
I just got a nrf52832 pca10040 board and I downloaded the last SDK nRF5 v11.
I downloaded Keil uVision5 and was able to load some examples and test them: nfc record_url...
