hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
Hello everyone,
I guess my question is more conceptual rather than a specific issue with the code.
I am working on a device featuring an nRF5340 chip and an nRF9160 chip...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
Am making a project based on NUS central demo and I can connect to our remote unit with the 52840DK, I can send data over a UART into it and I can get data out which is received...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
Hello,
I want to use external flash. I did some research on the subject. I am using SDK 2.6.1. I have a few questions.
1- Does the spi_flash example I examined work on...
I have a custom nRF9160 board running a modified asset_tracker program. I am using UART0 as a command line interface for testing and debugging. I can enter commands to setup...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
