Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I have a central application that runs on nRF52833 soc. I want to connect it with my nrf connect for mobile app, so I've created a new advertising packet in the advertiser...
Good day, sirs
I am trying to imply function that one central device could connect to max 3 devices, only one device active, while switch active device between the three...
Hi,
I'm working on SDK 15,
When initializing USBD using function app_usbd_init, I found that if APP_USBD_CONFIG_POWER_EVENTS_PROCESS = 0,
it disabled all USBD event...
HI everyone, i have a problem when implementing Butterworth bandpass filter in SAADC module to cancel out the noise of our ECG module.
I used " nrf_saadc_value_t m_buffer_pool...
---
I want to apply whitelist and peer manager to an existing project Now, the whitelist is not applied, and if you give the 'scan start' command, the scanned device lists...
Hi Team,
We are developing an application where we have PWM like pulses coming from our sensor. Max frequency of this would be around ~8k. We want to poll the number of...
Hi Team,
I am initialized to work on NRF52840 Dongle
Here I want to see the log or print statement for my developing purpose
i used tera term to view my log but no statements...
Hi,
I have 3 nRF5340 Audio DK's and want to decrease the sample rate and the bit rate. By now, I have changed the rates in the .config and autoconf.h files (from 48kHz to...
hello, team:
I'm new to the nrf5340 develop.I have installed the nrf connect SDK v2.0.2 many times.
when the installation end,I can only find nothing but the '.git' in...
Hi
The documentation of nRF5340 Audio Application of nRF Connect SDK 2.1.1 mentions "onboard hardware codec" and "external hardware codec".
From https://developer.nordicsemi...
I am using a development system that uses a Microchip MCP2515 chip which has the drivers included with Zephyr and everything works perfectly with 52840dk board. Who can tell...
Hi,
I am evaluating the nRF5340 Audio DK by applying the sample code nRF5340_audio.
I tried changing the frame to 7.5 ms by editing prj.conf as below and no audio came...
Hello everyone
i am used Arduino nano ble 33 board in that board nrf52840 is used anyone known how to increase Tx power of Bluetooth i am used Arduino ide for coding
I'm using version 2.0.2 of NCS
I have code working with nRF52840 in Zephyr
I need to move that code to nRF52832 (also in Zephyr)
My application is failing to start BLE...
