I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hello DevZone,
I want to transmit some connection information such as a Bluetooth address serially to my peripheral and have it add it to its whitelist.
I have read a...
Hello,
I'm am trying to use the UART0 bus on the network core at the address:
uart0: uart @ 41013000 {
compatible = "nordic,nrf-uarte" ;
reg = < 0x41013000 0x1000...
Hi,
ubuntu 20.3
vscode + nrf connect
when i creat project from sample code unicast_audio_client, i get the following compiling error message:
* Executing task: nRF...
Hey!
I have inherited a project with a nRF9160 + nRF52480 combination to do LTE and BLE communication.
The setup is as follows:
- nRF9160 using BSDlib @ NCS 1.5.0...
My Peripheral device (nrf Connect SDK, nrf52840) will pair using NFC with an Android (8.0.0) phone. But although the Nordic device shows it is connected (in its UART output...
This press release isn't clear on the exact nature of the LwM2M software stack used on the client side. Are we talking about Zephyr' s LwM2M subystem or AVSystem's Anjay ...
Hi, I am working on a pcb design utilising the nrf52840. I want to use a pcb antenna. I am a hobbyist so It’s very likely I’m misunderstanding something. I am interested in...
Hello,
I am using NRF5SDK V5.0.0. For a sample study, I need to use the bootloader. Can I boot over uart when we install mesh_bootloader_serial_armcc_nrf52832_xxAA.hex software...
Hi:
Currently I am testing to upgrade dual core application on nRF5340 DK, NCS version is V2.0.0.
The two core applications are written by myselves, not based on NCS routines...
Hi
using NRF5_SDK 17.0.2
I'm trying to better understand the DFU process, currently have a large number of questions. But mainly i would like to better understand the...
hello
I am watching this video to operate the nRF9160DK. The PIN number was written on the back of the nRF9160, so I skipped the video to 9:36 as instructed at 5:21, selected...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
