I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
I might be missing something obvious here, but when the device is flashed (via SES), the application works correctly. When the device is power cycled or reset due to the watch...
I already flash the ble_blinky example to the nrf52840-dongle using nrfconnect desktop. The question is it is possible to do DFU OTA via Bluetooth without nrf52dk or nrfconnect...
Hi,
Can mocks fully compensate for C++ standard features.? Is it recommended to write C++ code in nCS project by using these mocks.? What is the support for C++ operator...
Recently I develop products on nRF5340, I plan to make the full BLE stack run in the net-core, and app-core only runs application. It involves data exchenge between net-core...
Hello,
We have a application with soft device on nrf52832 with SDK 15.3 with 60 uA power consumption. It works as it seems for now.
We wanted to add DFU buttonless feature...
Hi,
We were using Nordic HAL for FEM modules to drive our PA/LNA using nRF52840 on zephyr (no NCS). It was only a basic configuration, where the PA and LNA pins were selected...
Hi.
I have a quick question regarding the RSSI Value of Messages sent in a Bluetoth Mesh Network.
So my question is: How exactly is the RSSI Value defined and how does...
I have a few questions about the DFU:
Is it necessary to flash everything together (Bootloader, DFU, APP) for the initial programming when testing buttonless secure DFU...
If you remove power from the beacon right around the time when the LED is going to start flashing to indicate power on, and do that a number of times you will see it will...
I successfully ran the asset tracker with the 9160DK and am able to receive all data correctly, certificates seem to be working, and everything works as mentioned in the asset...
Hello,
We have a large application using ESB to communicate between many nRF52840 devices. All devices are using firmware with SDK 17.0.2. These devices often switch from...
Hi,
I am using nrf52832 DK.
SDK 17.0.2 softdevice S132.
I am using freertos and running nrf52832 as a peripheral.
I want to put nrf52832 in sleep mode.
I am new...
Hello,
I am migrating code from nrf5_SDK_17.0.2 to nrf connect sdk v1.6.1. The board i am using is nrf52dk(nrf52832) connected with adafruit LSM6DSO.
Everything works...
